aimre
05-02-2005, 09:41 PM
Disclaimer: The following is provided as a GUIDE ONLY, and neither myself nor Ozhonda take any responsibility for the outcomes of someone else doing the following. You follow these steps at your own risk!
Aim: To remove any rust
Required: Sandpaper x2 (200+ grit and less than 200 grit)
Primer
Coloured Spray paint (auto1 and super cheap sell paints that match ur car paint code)
Clear top coat
Masking Tape
News Paper
Steps: Roughly Mask Around area where there is rust. This is so you do not sand n e more that U really need to.
Using ur rougher sand paper, sand the area where the rust is visible until u cant see anymore rust.
http://img.photobucket.com/albums/v47/aimre/sanding.jpg
Once all rust is removed, use the 200+ grit sandpaper to smoth out the area. Once the are is smothed, wipe residue with a dry cloth.
Remove the roughly applied and re-apply masking tape correctly and use newspaper to mask the car from over spray.
http://img.photobucket.com/albums/v47/aimre/masking.jpg
Now apply 1-5 coats of primer to the area (allow atleat 5 min between coats or refer to primer canisters instructions)
http://img.photobucket.com/albums/v47/aimre/primer.jpg
After final coat of primer allow 1hr before lightly sainding with 200+ grit for smoothness (again refer to primer instructions if in doubt)
Use a dry cloth to remove sanding residue
apply 2-4 coats of touch up spray paint alowwing 5-10 min between coats
5-10 min after final paint coat, applly 2-3 coats of clear coat.
allow 30 min for everything to dry then remove all masking slowly
http://img.photobucket.com/albums/v47/aimre/finished.jpg
Now ur done
Other comments: You shouldnt wash/polish for 5-7 days after painting.
You may also want to was car before comencing this, but make sure all is dry
:wave::wave::wave:
Aim: To remove any rust
Required: Sandpaper x2 (200+ grit and less than 200 grit)
Primer
Coloured Spray paint (auto1 and super cheap sell paints that match ur car paint code)
Clear top coat
Masking Tape
News Paper
Steps: Roughly Mask Around area where there is rust. This is so you do not sand n e more that U really need to.
Using ur rougher sand paper, sand the area where the rust is visible until u cant see anymore rust.
http://img.photobucket.com/albums/v47/aimre/sanding.jpg
Once all rust is removed, use the 200+ grit sandpaper to smoth out the area. Once the are is smothed, wipe residue with a dry cloth.
Remove the roughly applied and re-apply masking tape correctly and use newspaper to mask the car from over spray.
http://img.photobucket.com/albums/v47/aimre/masking.jpg
Now apply 1-5 coats of primer to the area (allow atleat 5 min between coats or refer to primer canisters instructions)
http://img.photobucket.com/albums/v47/aimre/primer.jpg
After final coat of primer allow 1hr before lightly sainding with 200+ grit for smoothness (again refer to primer instructions if in doubt)
Use a dry cloth to remove sanding residue
apply 2-4 coats of touch up spray paint alowwing 5-10 min between coats
5-10 min after final paint coat, applly 2-3 coats of clear coat.
allow 30 min for everything to dry then remove all masking slowly
http://img.photobucket.com/albums/v47/aimre/finished.jpg
Now ur done
Other comments: You shouldnt wash/polish for 5-7 days after painting.
You may also want to was car before comencing this, but make sure all is dry
:wave::wave::wave: